How Much To Install A Remote Start System

Download Article

Download Article

Ideally, remote starters should be installed past a qualified technician because improper installation can harm expensive vehicle control electronics. However, for someone familiar with electronics and vehicle repair, knowing how to install a remote starter in a car can salve money on installation costs and eliminate the frustration of finding a qualified installer. While this article provides some general instructions for wiring a remote starter, it varies by vehicle and remote starter model.

1. 

   one

   Make sure the remote starter y'all cull is compatible with your vehicle make and model. Read the box or contact the remote starter manufacturer to determine if it is uniform with your vehicle. You will want a starter that is compatible with your anti-theft system and secure.^[ane]

   • If it is not uniform with your anti-theft system, you will have to buy additional costly anti-theft bypass modules.

2. 

   2

   Read the installation instructions carefully. Installation instructions vary according to different brands and models of remote starters. Information technology is important to carefully read the installation instructions and find the wiring diagrams for your particular starter.

   • If you choose a used unit or one that does not include directions, check out online instructions before making a purchase. Brand certain the website is piece of cake to utilize and has complete, printable directions and wiring diagrams that conspicuously show how to install a remote starter in your car.

   Advertizing

3. 

   three

   Read the possessor's manual and repair guides for your vehicle. Go familiar with the wires in your vehicle by looking over the manual and repair guides. Some standard wire connections include the starter, ignition, power and accessory controls like heat and air-conditioning, security or alarm system, radio and power locks.

4. 

   iv

   Gather all the tools and equipment you will demand. Consult your manuals to determine which tools you volition need for your item starter and vehicle. You may require a utility pocketknife, wire cutters, wire strippers, soldering iron and solder, electrical tape, digital multimeter, wrenches and/or screwdrivers. A digital multimeter is recommended for testing during and later on installation.

   • Some remote starters will come with all the necessary tools so check your box. For instance, many systems come with an LED excursion tester to find the necessary wires for installation.
   • It is recommended that you solder all your wires together to form better connections. If yous choose to solder you lot will need a soldering atomic number 26 and safety spectacles.

5. 

   5

   Determine where to put the principal module and open the surface area. Information technology must be in a secure, subconscious location that won't require extending the supplied wires. The usual position is inside the lower dash underneath the steering wheel. This style y'all can connect straight to the ignition wiring.

   • Don't identify it in the engine compartment or whatsoever area where it will be exposed to extreme vibration or heat.
   • Possible alternative locations include spaces to a higher place the radio or glove compartment, the center console and above the dashboard fuse box.

6. 

   half dozen

   Become over the machine to make sure everything is working properly prior to installation. Check the battery, switches, lights and other systems. If any electrical systems are non working correctly and then you lot should fix them prior to beginning your installation.^[2]

7. 

   7

   Remove the seat where the control module will be installed if possible. Removing the seat will give y'all more room to work while installing the organization. If you cannot remove the seat and so slide the chair all the style backwards.

8. 

   8

   Disconnect the bombardment. When working on the electrical system of your vehicle it is safer to disconnect the battery to preclude any shocks. To test the wires you volition need to have the battery continued but disconnect it while you lot are soldering wires together to exist safe. When testing the wiring with the bombardment connected, brand sure you practise not probe any air purse circuit. Most of these are encased in a yellowish comprehend for safety.^[three]

   Advertisement

1. 

   1

   Remove the console covering under the steering bicycle. Employ a screwdriver to remove the panel roofing the underside of the steering column. This is where you lot will access the wires to connect the starter.^[4]

   • If the console is not attached with screws and so you might require a socket set to remove basics securing the panel.
   • Depending on your vehicle you may besides demand to remove the lower steering column cover to admission the ignition switch harness. If your vehicle has an anti theft system, it is probable that you will need to remove this cover.
   • If you lot choose to connect your remote starter to other functions such as the door locks and overhead lights then you lot will need to remove the kick panel as well. This is located on the lower left-hand corner of the driver's foot box.

2. 

   2

   Connect all your wires properly. It is very important that y'all securely connect all your wires. Loose wires can cause injury or major property impairment. It is best to solder all your connections to ensure that they are strong. You should also use estrus shrink tubing where possible and a skillful quality electric tape where yous cannot.

   • To connect wires first strip away almost 1/two-one inch (i-2.5 cm) of the blanket effectually the wire. If there are ii wires then split them and insert the attaching wire between them. Wrap the attaching wire around the stripped wire and solder them together using the soldering iron. In one case they are deeply attached, wrap electrical tape around the connection and use ties to agree them in place. Lightly tug on the wires to make sure they exercise non become loose.

3. 

   3

   Connect the ground wire. The basis wire volition be part of the starter and is often black. Connect this by screwing through the ring concluding into a make clean, unpainted metal surface in the kick panel surface area. This wire is very important for the proper functioning of your vehicle.

   • Because it is so important, it is amend to connect the ground wire to a location in the kick panel equally opposed to being close to the ignition switch in the dash. Also, it is better to utilize a split grounding location to prevent feedback through wiring that may cause estimator failures.

4. 

   4

   Locate the 12V constant wire on the vehicle and attach the power wire of your system to it. The 12V abiding wire is the one attached to the bombardment and is commonly plant in the bundle of wires attached to the ignition switch. You can locate this wire by reading the vehicle'southward manual and repair guides or testing with the multimeter.^[5]

   • If you run into whatever yellow or otherwise noticeable wires, do not touch them! These are the airbag wires and must not be tampered with or unplugged.
   • To test the power wires using the multimeter attach it to the wire when the car is off and the central is out of the ignition. It should read around 12V (or the bombardment voltage) constantly.
   • Some vehicles will have more than than one 12V constant wire. In this case place which is fused at a higher number of amps and attach your master power wire to this one. If your starter has two power wires, attach the second ability wire on the starter to the boosted 12V constant wire.
   • Use a soldering iron to connect all wires. This keeps them from falling apart and potentially damaging your vehicle. Add further protection by taping them completely.

5. 

   5

   Find and attach the accessory wire. The accompaniment wire supplies ability to oestrus and ac controls and supplies 12V when the key is in the showtime (accompaniment) position. Attach the accessory wire on the starter to the accessory wire on the vehicle.^{[half dozen]}

   • To discover this wire attach the multimeter while the key is in the "off" position. The voltage should be aught in this position. Plough the key into the start position but no farther. If you have found your accessory wire, the voltage volition now read effectually 12V (11.v-14V). Cheque that the voltage goes to nil 'while' you are cranking the engine (it will read 12V before and after cranking).^[seven]
   • Some vehicles might have more than i accessory wire to control all the functions. In this case apply a relay to connect additional wires.

6. 

   6

   Locate and connect the ignition wire. The ignition wire supplies ability to the fuel pump and ignition system and will exist attached to the ignition switch under the steering bicycle. The vehicle manual or repair guides should tell you which color this wire should be. Connect the ignition output wire on the remote starter to this wire.^[8]

   • One time you have located this wire y'all can confirm its identity using the multimeter. Adhere the multimeter to the wire while it is continued to a good ground wire and it should prove no voltage. Plough the key to the commencement position and the voltage should still read zero. In the second position, before starting the motorcar, in that location should be a voltage displayed on your multimeter. If at that place is, then you have identified the correct wire, if not then you must try again to locate your ignition wire.
   • Some vehicles take more than one ignition wire. If so, utilise a relay to connect all additional ignition wires.

7. 

   7

   Observe and adhere the starter wire. This volition only prove a voltage while the vehicle is beingness cranked, or turned on. It supplies power to the starter solenoid when turning your vehicle on. Connect the starter wire output on your remote starter to this wire by soldering the wires together.^[9]

   • Locate a potential starter wire to examination with the multimeter. The voltage should be zip when the key is in all positions except while cranking the engine. If you lot recall you lot have found the wire, outset with the key in position two and then creepo the engine. The voltage should read zero while the key is in position two, evidence 12V while cranking and then go back to zero if yous release the key before the engine turns over.^[10]

8. 

   viii

   Connect the parking low-cal and brake wires. The restriction wire is unremarkably plant at the switch harness higher up the restriction pedal but can too be institute along with the parking light wires in the kick panel on the way to the rear of the vehicle. Connect these wires to the parking light and brake output wires on the remote starter.^[11]

   • To find the restriction wire press the brake pedal downwardly while the car is on and utilize the multimeter to test the wire. The multimeter should read between 11.5-14V while the brake is pressed downward.
   • The brake wires in particular are important to connect considering they prevent someone from driving off in your car while information technology is running from the remote starter.

9. 

   9

   Locate and connect the tachometer wire to the tachometer output wire on the remote sensor. This is required past the remote starter then that it disengages the starter once the car has started. It tin can usually be plant in the engine distributor or coil pack.^[12]

   • To locate the tachometer wire look for the engine distributor past following the spark plug wires to where they junction at a distributor and find a small wire harness which should have a tachometer reference. Alternatively see the owner's manual to make up one's mind the recommended tachometer wire'due south location.

10. 

    ten

    Connect any security, anti-theft and other optional components. Some systems might accept boosted steps for connecting to the door locks of the vehicle. Others might need a special system for getting around the anti-theft organisation that exists in your car. As ever consult the manual or manufacturer of your remote sensor to find out which extra features your system has and where you should connect them.

    • To connect to the door locks you tin locate the wires in the driver's side door. You lot may need an external relay, of which there are many dissimilar kinds. All the same the four near common include positive trigger, negative trigger, reverse polarity and multiplex door lock systems. Consult your vehicle transmission or repair guides to determine which system your vehicle uses.

11. 

    11

    Use a relay to connect additional wires if there is more than 1 wire for ability, accompaniment or the starter. A relay allows multiple wires to be continued together. In that location are many different designs, shapes and sizes but they all perform the aforementioned bones function. Connect the wires to the relay past wrapping them around the pins.

12. 

    12

    Secure wires with necktie wraps or screws to proceed them away from moving parts. This volition protect the wires and make the installation look tidy and neat.

13. 

    13

    Connect the battery and exam to meet that all the functions work. Test your remote start and keyless entry systems as well every bit your brakes and brake lights to brand sure everything has been connected properly and is working. If something fails to work, go back and cheque all the wires you have connected to see what went wrong.

    • Make sure yous test your vehicle to brand certain it volition start, run, and drive using your key commonly. This will insure the installation did not affect whatsoever normal vehicle operations or crusade any nuance lights to illuminate abnormally.

14. 

    fourteen

    Replace the boot panel and the panel covering the ignition switch. Push the remote sensor and the wiring into the compartment and encompass with the console. Screw (or ratchet) the panel into identify. Make sure not to pinch or screw into any wiring during installation.

    Advertising

Add New Question

• Question

  When my remote starter is on, the park lights do non plow on. What does that hateful? And how do I fix it?

  

  Check your parking lights connectedness - that seems to be the only possible problem unless you have a faulty system.

• Question

  Will the installation of the remote starter void the manufacturer'due south warranty if not installed by the dealership?

  

  Yes, almost manuals country that this system is required to exist installed by a professional.

• Question

  Is it necessary to connect a remote starter to any other components of my car?

  

  No, you don't need to connect the remote starter to any other components after post-obit the instructions here.

• Question

  After installing the remote starter, my car seems to be struggling to have enough ability to run the engine and electronics, but if I use the normal first this does not happen. What should I do?

  

  The system may be either drawing too much power, or, when you use the remote kickoff, the engine may start, only not generate enough power. Become information technology checked out from a certified dealer.

• Question

  Why did my check engine light come on later on doing this?

  

  There are different things that can crusade a check engine lite to turn on. It may not have anything with the remote starter. You should go to a car identify that can employ a special diagnostic tool to notice out. Many car places, including Automobile Zone, volition practise this for free.

• Question

  How practice I tell if a vehicle already has a remote starter?

  

  Look on the windshield, most likely close to the rear-view mirror. If at that place's a remote starter, there'll exist a component like to the object in the man'south hand from Stride 10. That's the sensor that receives the signal from the key fob.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

Video

• Continue wires away from sharp objects under the dashboard. If a wire is cut or becomes loose it can cause damage to the vehicle that may be expensive to repair.

• The installation of the remote start organization on newer vehicles that accept factory security systems and code keys may require specialized equipment that are but bachelor to the dealers. Brand sure you lot accept consummate directions, proper tools and any specialized equipment before attempting installation.

• Take your time and be methodical. It is very important to be thorough so that y'all practice not injure yourself or damage your vehicle.

• Soldering your wires together volition make them more secure and less likely to cause problems in the future.

• Do not endeavor and use a remote start system not designed to piece of work with your vehicle.

• Use a relay to connect additional wires if there is more ane wire for ability, accessory or the starter.

Advertising

• Be careful when working with electrical wires as they can shock you and cause injury.

• Failure to install your remote sensor correctly can cause injury and belongings damage.

• Exercise not operate your remote start system in a closed garage or a buildup of carbon monoxide gas will occur.

• If you are unsure or unfamiliar with electrical systems, do not endeavor to install your remote starter system on your own. It is much meliorate and safer to hire a qualified technician to consummate the installation.^[13]

Advertisement

Things Y'all'll Need

• Utility knife
• Wire cutters
• Wire strippers
• Soldering iron and solder
• Electric tape
• Heat shrink tubing
• Heat gun
• Digital multimeter
• Wrenches
• Screwdrivers
• Vehicle wire diagrams

About This Article

Article Summary 10

To install a remote starter in a car, disconnect the battery and remove the panel roofing nether the steering bike. Next, connect the starter's blackness ground wire to the boot panel and solder the starter's power wire to the 12V wire attached to the car battery. Attach the accessory wire, then connect the ignition wire to the ignition output wire on the remote starter. Lastly, attach the starter wire and connect any security components y'all have. For tips on keeping wires tidy, read on!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 475,882 times.

Did this article help y'all?

Source: https://www.wikihow.com/Install-a-Remote-Starter-in-a-Car

Posted by: bakerlifuld1961.blogspot.com

Share this post